How to Get Scratches Out of Acrylic Surfaces
Acrylic — polymethyl methacrylate, or PMMA — sits around 3 on the Mohs hardness scale, roughly the same as a copper coin. That is why a ring, a dropped key or a gritty cloth leaves a white line so easily. The good news is that the same softness that makes acrylic scratchable also makes it repairable: a scratch is displaced or removed material, and material can be levelled and polished back to a clear surface.
The mistake is attacking a scratch with one aggressive product. Success comes from a graduated sequence — refine the scratch with a coarser abrasive, remove those scratches with a finer one, then restore gloss with a finishing compound. Light scuffs never need abrasion at all; plain white toothpaste on a damp cloth will lift them. Anything you can feel with a fingernail needs the full sequence, and anything deeper than about a millimeter needs a new panel or a professional.
What You'll Need
Gather everything before you start so the surface is never left half-treated.
- 600-grit wet/dry sandpaper
- 1200-grit wet/dry sandpaper
- Sanding block or a flat rubber eraser
- Spray bottle with water and a drop of dish soap
- Acrylic finishing compound or plastic polish
- Plain white toothpaste (non-gel, no whitening beads)
- Masking tape
- Four clean microfiber cloths
Safety first: Sand wet only; dry friction melts the acrylic and gums the paper. Work on a small hidden area first, and keep the paper flat — a fingertip concentrates pressure and sands a hollow into the surface.
Step-by-Step Guide
- 1
Measure the depth.
Drag a fingernail across the scratch at a right angle. If it glides over, the mark is surface-level and toothpaste may be enough. If it catches, the scratch has depth and needs wet sanding. If it catches hard and the plastic looks white at the bottom, the damage may be too deep to remove safely.
- 2
Clean and tape the area.
Wash the panel with dish soap and water and dry it completely. Run masking tape along the edges of the repair area so the sanding block does not wander onto untouched gloss and leave a visible transition.
- 3
Start with 600 grit, wet.
Wrap 600-grit paper around a flat block, wet it with the soapy water, and sand the scratch in straight passes, alternating direction by 90 degrees between passes. Use light pressure and keep the paper wet; the goal is to level the area around the scratch, not to dig at the scratch itself.
- 4
Check the scratch as you go.
Wipe the area dry every ten or so passes and look at it under a light held at a low angle. Stop sanding when the white line is gone. Continuing past that point removes material for no reason and makes the repair harder to blend.
- 5
Refine with 1200 grit.
Switch to 1200-grit paper on the same block, keep it wet, and sand the hazy area in overlapping passes until the 600-grit scratches are replaced by a finer, more even haze. This step is what makes the final polish possible; skipping it leaves coarse scratches that polish cannot hide.
- 6
Polish with finishing compound.
Apply a pea-sized amount of acrylic finishing compound to a microfiber cloth and work it over the area in small circles with moderate pressure. Buff with a clean cloth, then inspect from several angles. Two or three short sessions beat one long one that heats the plastic.
- 7
Try toothpaste before sanding light marks.
For a scuff you can barely feel, put a dab of plain white toothpaste on a damp microfiber cloth and rub the mark for 30 seconds, then wipe clean. Toothpaste contains a fine abrasive that is gentle enough for surface haze but will not remove a scratch with depth.
- 8
Protect the repaired area.
Wipe off all compound residue with a damp cloth, then apply a thin coat of non-abrasive wax or plastic protectant and buff it clear. The coating does not harden the acrylic, but it fills the micro-texture and makes future scuffs easier to wipe away.
What to Avoid
- Dry sanding — friction heats PMMA above its softening point, and the paper instantly clogs with melted plastic.
- Grits coarser than 600 — they cut deep grooves that take far longer to refine and can leave a visible dip in the panel.
- Acetone, lacquer thinner and nail polish remover — they dissolve the surface and turn a scratch into a permanent cloudy crater.
- Ammonia-based glass cleaner on the finished repair — it attacks the polished surface and can craze the whole panel.
- A high-speed machine buffer held in one spot — the heat builds quickly and can distort the sheet before you see any change.
Daily Care Tips
- Dust acrylic with a microfiber cloth rather than a paper towel, which drags grit across the surface.
- Use coasters, placemats and cutting boards; the cheapest repair is the scratch that never happens.
- Wipe spills with mild soap and water, then dry — never let a cleaner sit on the panel.
- Keep rings, keys and belt buckles away from the surface when reaching across a table or counter.
- Reapply a non-abrasive protectant every few months on high-touch pieces such as tables and display covers.
Frequently Asked Questions
Can toothpaste really remove scratches from acrylic?
It works on surface haze and very light scuffs, not on scratches you can feel. Use plain white paste, not a gel or a whitening formula with beads, and rub a small area with a damp cloth for about 30 seconds. The abrasive is fine enough to polish without leaving noticeable marks. If the scratch is still visible after two attempts, move up to the wet-sanding sequence.
How much acrylic can I sand away?
Very little — a few thousandths of an inch at most. Each grit removes material, and a deep dip creates an optical distortion that is more obvious than the original scratch. As a rule, if the scratch disappears after a dozen passes with 600 grit, the repair is safe. If you are still sanding after several minutes, stop and accept the mark or replace the panel.
Will sanding leave the acrylic cloudy?
It will look cloudy until the final polish, which is normal. The 1200-grit haze is the intermediate stage; the finishing compound restores clarity by smoothing the microscopic peaks left by the paper. If cloudiness remains after polishing, the usual cause is skipping the 1200 step or using too little water during sanding.
Can I use a power polisher on acrylic?
Only at low speed, with a soft foam pad and constant motion. Acrylic has a low melting point and a polisher held still for even a few seconds generates enough heat to distort the surface. For most household repairs, hand polishing gives a more predictable result and removes less material.
Final Thoughts
Refine the scratch in stages, polish only after the surface is uniform, and acrylic will come back clear instead of turning into a permanent white scar.